For Toyota Corolla Matrix Pontiac Vibe 1.8L 2.4L 2009 2010 Fuel Pump Assembly

Description

The Function of the fuel pump is to supply fuel at a certain pressure to the engine fuel injection system.
However,the fuel pump have a limited life.If you notice any of the following signs with your car:
(1).Engine Sputtering at High Speeds
(2).Decreased Fuel Pressure
(3).Losing Power when the Vehicle is under Stress
(4).Inability to accelerate
(5).Decreasing Gas Mileage
(6).Engine Not Starting
This may indicate that you need to replace the fuel pump
Fuel Pump Replacement Guideline:
Please Note the following before replacing the fuel pump:
1.Ensure that you are in a well ventilated and level work area.
For Toyota Corolla Matrix Pontiac Vibe 1.8L 2.4L 2009 2010 Fuel Pump Assembly
The Function of the fuel pump
is to supply fuel at a certain pressure to the engine fuel injection system.
However,the fuel pump have a limited life.If you notice any of the following
signs
with your car:
(1).Engine Sputtering at High Speeds
(2).Decreased Fuel Pressure
(3).Losing Power when the Vehicle is under Stress
(4).Inability to accelerate
(5).Decreasing Gas Mileage
(6).Engine Not Starting
This may indicate that you need to replace the fuel pump
Fuel Pump Replacement Guideline
:
Please Note
the following before replacing the fuel pump:
1.Ensure that you are in a well ventilated and level work area.
2.Use approved safety glasses or goggles when working on any motor vehicle.
3.The gasoline is sucked out of the tank and stored in a container dedicated to gasoline.
Picture(A)
Disconnect the ground (
negative
) cable of the battery and ensure that it does not accidentally spark while working.
Picture(
B
)
Locate and remove gas tank filler neck mounting bolts or remove the filler tube from the tank. This will aid the fuel removal especially if you had problems accessing through the filler neck.
Picture(
C
)
Located the electrical connector for the fuel pump and fuel level sender which will be in the same wiring harness. If access if difficult or you can't see them wait until the tank is lowered slightly to undo the connector. Inspect electrical connector for burns or heated spots and replace if damaged. A burned connector can cause a pump to fail intermittently.
Picture(
D
)
There will be fuel vapor lines as part of the EVAP system these will need to be removed or disconnected.
Picture(
E
)
Locate and release tank holder supports, there are two in most cases. Remove the mounting bolts at this point the tank will become loose but may not come out.
Picture(
F
)
Lower the tank and release top mounted fuel lines or electrical connectors if any. Continue to remove the tank.
Picture(
G
)
Remove the tank, this will expose the fuel pump retainer ring. Use an aerosol cleaner to remove dirt and debris from the area. This will keep the inside of the fuel tank clean when performing the repair.
Picture(
H
)
Remove fuel pump mounting bolts or retainer ring to access the fuel pump module and remove the unit. Use a hammer and punch to remove the ring counterclockwise.
Picture(
I
)
Remove the fuel pump which will be attached to the mounting plate or positioned down inside the tank held by plastic retainer clips.
Picture(
J
)
Remove the fuel pump from the tank.
Item Specifics
Drive Type
Electrical
Fuel Type
Gas
PSI
45-55
Gallons Per Hour (GPH)
50-60
Placement on Vehicle
Rear
Please Note
2WD
Outlet Type
Recessed Quick Connect
Outlet Size
3/8
Inlet Type
Strainer
Inlet Count
1
Outlet Count
1
Terminal Type
Blade
Pin Count
4
Terminal Gender
Male
Connector Gender
Female
Internal Or External Strainer
Internal
Placement on Vehicle
In Tank
Wiring Harness Included
No
Condition
New
Voltage
12.0 2H
Gasket or Seal Included
No
Float Included
Yes
Package Contents
Fuel Pump Module Assembly w/Float Arm
Interchange Part Number
E8874M,E3781M,FG0938,P76578M,SP9165M,69907
OE/OEM Part Number
88973532,88974257,88974776,19185090,7702002181
Fitment Type
Direct Replacement
Warranty
2 Year
Black Pressure Sensor Included
No
Color
White
Custom Bundle
No
OE Spec or Performance/Custom
OE Spec
Modified Item
No
Mounting Hardware Included
No
Brand
Fuel_Kingparts
Manufacturer Part Number
KF05315302ING
Payment
We only accept payment through PayPal.
Shipping
All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
Returns
All of our brand new items come with a 60-Days money-back guarantee.
Contact Us
Any question, please contact us by email on working days.
Warning
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Best Sales
For 2004 2005 2006 2007 2008 Ford F-150 4.6L 5.4L Fuel Pump E2434M
USD 57.49
For Chevy C1500 C2500 C3500 K1500 K2500 K3500 GMC C1500 C2500 C3500 Fuel Pump
USD 54.74
For 2003 2004 Ford Expedition V8 5.4L Fuel Pump E2360M
USD 47.49
For Pontiac G6 Chevy Malibu 2.4L 3.5L 3.6L 3.9L Saturn Aura 2.4L 3.5L Fuel Pump
USD 72.49
For Dodge Ram 1500 2500 5.2L 5.9L 1996-1997 Fuel Pump w/Sending Unit E7093M
USD 64.99
Newly Listed
Fuel Pump Fit For Honda CR-V L4 2.4L 2007 2008 2009 2010 2011
USD 55.99
Fuel Pump Fit For GMC Sierra 3500 V8 6.0L 2004-2006 8.1L E3617M
USD 53.99
For Chevrolet Malibu Buick LaCrosse Regal Cadillac XTS Fuel Pump Electric E4045M
USD 72.99
For 1991-1993 Ford Thunderbird Mercury Cougar 5.0L Fuel Pump Moudle Assembly
USD 54.99
Fuel Pump Fit For Honda Pilot V6 3.5L 2012 2013 FG1553 SP8967M
USD 62.99
Terms & Contact
Payment Policy
Shipping Policy
Return Policy
FAQ
About Us
For Toyota Corolla Matrix Pontiac Vibe 1.8L 2.4L 2009 2010 Fuel Pump Assembly
The Function of the fuel pump
is to supply fuel at a certain pressure to the engine fuel injection system.
However,the fuel pump have a limited life.If you notice any of the following
signs
with your car:
(1).Engine Sputtering at High Speeds
(2).Decreased Fuel Pressure
(3).Losing Power when the Vehicle is under Stress
(4).Inability to accelerate
(5).Decreasing Gas Mileage
(6).Engine Not Starting
This may indicate that you need to replace the fuel pump
Fuel Pump Replacement Guideline
:
Please Note
the following before replacing the fuel pump:
1.Ensure that you are in a well ventilated and level work area.
2.Use approved safety glasses or goggles when working on any motor vehicle.
3.The gasoline is sucked out of the tank and stored in a container dedicated to gasoline.
Picture(A)
Disconnect the ground (
negative
) cable of the battery and ensure that it does not accidentally spark while working.
Picture(
B
)
Locate and remove gas tank filler neck mounting bolts or remove the filler tube from the tank. This will aid the fuel removal especially if you had problems accessing through the filler neck.
Picture(
C
)
Located the electrical connector for the fuel pump and fuel level sender which will be in the same wiring harness. If access if difficult or you can't see them wait until the tank is lowered slightly to undo the connector. Inspect electrical connector for burns or heated spots and replace if damaged. A burned connector can cause a pump to fail intermittently.
Picture(
D
)
There will be fuel vapor lines as part of the EVAP system these will need to be removed or disconnected.
Picture(
E
)
Locate and release tank holder supports, there are two in most cases. Remove the mounting bolts at this point the tank will become loose but may not come out.
Picture(
F
)
Lower the tank and release top mounted fuel lines or electrical connectors if any. Continue to remove the tank.
Picture(
G
)
Remove the tank, this will expose the fuel pump retainer ring. Use an aerosol cleaner to remove dirt and debris from the area. This will keep the inside of the fuel tank clean when performing the repair.
Picture(
H
)
Remove fuel pump mounting bolts or retainer ring to access the fuel pump module and remove the unit. Use a hammer and punch to remove the ring counterclockwise.
Picture(
I
)
Remove the fuel pump which will be attached to the mounting plate or positioned down inside the tank held by plastic retainer clips.
Picture(
J
)
Remove the fuel pump from the tank.
Item Specifics
Drive Type :
Electrical
Fuel Type :
Gas
PSI :
45-55
Gallons Per Hour (GPH) :
50-60
Placement on Vehicle :
Rear
Please Note :
2WD
Outlet Type :
Recessed Quick Connect
Outlet Size :
3/8
Inlet Type :
Strainer
Inlet Count :
1
Outlet Count :
1
Terminal Type :
Blade
Pin Count :
4
Terminal Gender :
Male
Connector Gender :
Female
Internal Or External Strainer :
Internal
Placement on Vehicle :
In Tank
Wiring Harness Included :
No
Condition :
New
Voltage :
12.0 2H
Gasket or Seal Included :
No
Float Included :
Yes
Package Contents :
Fuel Pump Module Assembly w/Float Arm
Interchange Part Number :
E8874M,E3781M,FG0938,P76578M,SP9165M,69907
OE/OEM Part Number :
88973532,88974257,88974776,19185090,7702002181
Fitment Type :
Direct Replacement
Warranty :
2 Year
Black Pressure Sensor Included :
No
Color :
White
Custom Bundle :
No
OE Spec or Performance/Custom :
OE Spec
Modified Item :
No
Mounting Hardware Included :
No
Brand :
Fuel_Kingparts
Manufacturer Part Number :
KF05315302ING
Payment
Shipping
Returns
Contact Us
Warning
We only accept payment through PayPal.
All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days.
All of our brand new items come with a 60-Days money-back guarantee.
Any question, please contact us by email on working days.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
All rights reserved.